Winegard TV Antenna MV 4002 User Manual

®
WINEGARD  
TM  
Movin’ View  
Digital Satellite Mobile Antenna for Two Receivers  
for Use While Stationary or In-Motion  
Model MV-4002  
Made in the U.S.A. U.S. Patent Nos. 6,023,247; 6,188,300  
Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000  
Printed in U.S.A. © Winegard Company 2005 2452062 Rev. 5/05  
1
 
Quick Reference Guide  
NOTICE!  
This model is PRESET for DIRECTV® receivers.  
®
®
If you have a DISH Network or ExpressVu (Canada) receiver,  
you must change the numbered switches inside the dome.  
TO CHANGE SWITCHES INSIDE DOME —  
1. Remove screws holding dome to base and remove dome. Place dome in safe spot to avoid damage.  
Switches will be set at 101° for DIRECTV®. You will be changing these switches.  
Models MV-4002, MV-4000, MV-4005  
MOUNTING  
(#1 represents Switch DOWN; #0 represents Switch up)  
1
0
2
3
0
4
5
0
6
0
7
0
8
1
OPTION A  
Sat. Rcvr.  
...................................  
DIRECTV  
(FACTORY PRESET)  
Mt. Option  
Switch Set Position  
MOUNTING OPTIONS  
SHOWN BELOW  
1
0
2
0
3
0
4
0
5
0
6
0
7
0
8
1
A
0 = UP  
1 = DOWN  
0
0
DIRECTV  
B
A
B
A
B
1
0
1
0
1
0
0
0
1
1
0
0
0
0
0
0
1
1
1
1
0
0
0
1
1
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
DISH NETWORK  
DISH NETWORK  
ExpressVu  
ꢀꢀꢀ  
ExpressVu  
2. Determine which programming you will be using. This will determine how you set your switches.  
For DISH Network set switches to 119°.  
For ExpressVu®, set switches to 091°.  
MOUNTING  
OPTION A  
MOUNTING  
OPTION A  
1
0
2
3
0
4
1
5
1
6
0
7
8
1
0
2
3
4
1
5
0
6
7
1
8
1= DOWN  
0= UP  
0= UP  
1= DOWN  
1
1
1
0
0
0
1
ꢀ ꢀ ꢀ  
ꢁ ꢁꢁ  
ꢀ  
ꢁ  
MOUNT OPTIONS A AND B  
FIGURE 1A, OPTION A  
FIGURE 1B, OPTION B  
CENTER LINE OF VEHICLE  
CENTER LINE OF VEHICLE  
MV-4002  
MV-4002  
BASE FOOT  
(MUST BE PARALLEL  
TO CENTER LINE)  
BASE FOOT  
(MUST BE PARALLEL  
TO CENTER LINE)  
DIRECTV® receivers must be set to the two satellite, oval dish setting. Refer to your receiver manual.  
DISH Network receivers must either have the check switch set for SW42 or unknown, no satellite found. See  
page 5.  
The satellite system has two modes of operation; Tracking Mode and Sleep Mode. When you first turn the  
unit on it enters Tracking Mode. In this mode the unit will search and actively follow the satellite as the vehicle  
travels. Tracking Mode ends when the unit has successfully finished its search and the vehicle has not moved  
for six minutes.  
Sleep Mode, this is the unit at rest mode. During Sleep mode the dish will toggle between primary and sec-  
ondary satellites as you change channels with the remote. The unit enters Sleep mode about six minutes after  
a successful search if stationary, or six minutes after the vehicle stops moving.  
3
 
Operation  
b. If it moves off the signal , it is in an effort to verify  
the signal and it should return to the signal shortly.  
1. Turn on receiver and television set. The MV-4002  
must be connected to a receiver that is plugged  
into 120 VAC.  
5. After the unit has verified that it has the correct  
satellite, it will continue to fine tune for about 6 min-  
utes (unless the vehicle is in-motion, see 7 below).  
2. Verify that you are getting the receiver’s menu  
screens on the television. These screens are avail-  
able with or without the dish finding the signal.  
6. At the end of 6 minutes the unit will move to check  
it’s alternate satellite then move back to the primary  
and go to sleep. See page 3 for a description of  
Sleep Mode.  
3. Turn the power switch on for the MV-4002.  
The dish should start moving, making one or two  
revolutions before it stops to acquire GPS. This can  
take a few moments or up to 10 minutes. Normal  
operation will be less than a minute.  
7. While the vehicle is in motion, the unit will not en-  
ter sleep mode after a successful search. Instead it  
will wait until the unit has stopped moving for 6 min-  
utes before entering sleep mode.  
4. Once the unit has acquired GPS, the dish will  
begin its search.  
a. The dish will pause on the signal long enough to  
determine which satellite it has found.  
8. If you do not have signal, see Troubleshooting,  
p. 11.  
Recovery from Signal Interruption—  
While traveling, the signal will be interrupted  
when the line of sight to the satellite is blocked.  
Signal is acquired again after line of sight is restored.  
If signal is interrupted for more than 15 seconds, the  
system automatically enters the search routine. The  
length of time for the TV picture to recover de-  
pends on the receiver model you are using.  
The unit must travel in straight  
line for 10 seconds when starting  
to operate in motion.  
4
 
To toggle between satellites when subscribing to multi-satellite programming—  
While in Sleep Mode, the MV-4002 will toggle be-  
tween the primary and seconday satellites for either  
DISH Network or DIRECTV. Both have program-  
ming on more than one satelite.When a channel is  
selected on the remote control and is not on the  
satellite currently selected, the unit will automati-  
cally move to the correct satellite.  
If a switch other than SW42 appears, or you  
have an X in one of the boxes below the satel-  
lites, repeat Check Switch Steps.  
5. Your system is now set up to toggle between sat-  
ellites. It will automatically move to the correct  
satellite when a channel is selected with your remote  
control.  
DIRECTV programming  
1. DIRECTV receivers must be set for oval dish 2  
sat selection to enable toggling between primary  
101°W satellite and alternate 119°W satellite only.  
(Consult receiver manual for procedure.) After  
receiver is set for the correct dish selection, when  
you request a channel located on a different satel-  
lite, the unit will automatically move to that  
satellite.  
NOTE: Once these steps are completed, you  
won’t have to perform this test again, unless  
Check Switch was performed on another satel-  
lite dish, such as a home dish.  
Toggle: Your Winegard Automatic  
satellite dish will move from the  
primary to the alternate satellite in  
order to receive multi-satellite  
programming.  
DISH Network programming (DISH 500)  
!
DISH Network receivers must have the “SW42”  
switch installed in order to toggle between the pri-  
mary 119 satellite and the alternate 110 satellite.  
(Consult your receiver manual for the procedure to  
reach the “check switch” menu.)  
To install the “SW42” switch:  
1. Before turning on your MV-4002 system, make  
sure that your satellite receiver and television are  
turned on and your receiver is on the “point dish”  
menu. (Consult your owner’s manual to reach this  
menu.)  
2. While the vehicle is stationary, turn on the MV-  
4002 system and wait for signal acquisition on  
satellite 119.  
3. After signal is acquired, the system will continu-  
ously track the signal for approximately 6 minutes.  
At the end of 6 minutes, the unit will enter sleep  
mode. You now have 6 minutes to complete  
Check Switch test. Consult your receiver manual  
for instructions on running this test. Be sure that  
Superdish andAlternate are unchecked if applicable.  
Onscreen options may vary by receiver.  
Install Summary  
SW42  
Input:  
1
1
1
1
Satellite:  
Polarity:  
119  
119  
110  
110  
Odd Even Odd Even  
Status:  
Satellite reception verified  
Superdish  
Cancel  
Alternate  
Help  
4. During the Check Switch Test, the receiver will  
begin checking the switch by toggling between  
satellites. When this is completed, SW42 will ap-  
pear on the screen. It will be at the top of the  
screen, satellite designations will be below, show-  
ing odd and even transponders. See illustration.  
Test  
Check Switch screen display  
NOTE: Be sure the “Superdish” and “Alter-  
nate” boxes ARE NOT checked.  
5
 
Parts Included • Tools Needed • How to Unpack  
PARTS INCLUDED:  
1 Radome  
1 large yellow spade connector  
1 Power switch  
2 small red spade connectors  
1 Wall plate (white)  
1 Surface mount box  
1 Cable entry plate  
All required screws and washers  
1 base with electronics, dish, single LNBF  
30’ power cable and 30’ coaxial cable  
TOOLS NEEDED FOR UNPACKING & INSTALLATION:  
Level  
Phillips screw driver #2  
Drill w/3/4” bit  
Sealant (consult RV manufacturer for proper type  
for your roof material)  
1-1/4” hole saw (if mounting switch in wall)  
3/8” Box/Open end wrench for dome screws  
7/16” Open end wrench  
UNPACKING THE UNIT  
1. Open box and remove packing material.  
If using knife to open  
carton, BE CAREFUL.  
!
Do not cut the dome on  
LIFT UNIT STRAIGHT UP  
OUT OF CARTON!  
the unit.  
BE CAREFUL when  
removing unit. Dome is  
!
attached to base by  
ONLY THREE PEICES  
OF TAPE!  
2. Lift unit out of box vertically. Do not turn box and  
“roll” out, or turn upside down to remove.  
USE 2 PEOPLE  
when removing the unit  
from the carton.  
Do not paint dome!  
Painting dome will cause  
signal degradation.  
!
6
 
Base Diagram  
SWITCH LOCATION  
FIGURE 2  
(SIDE OF BOX, SEE PAGE 3)  
CONTROL  
BOX TO LNBF  
COAX CABLE AT  
CONTROL BOX  
EL MOTOR  
GPS ANTENNA  
CABLE  
+12VDC  
POWER CABLE  
GPS  
ANTENNA  
CENTER  
LINE OF THE  
VEHICLE  
CONTROL  
BOX  
(DETAIL  
BELOW)  
FOOT  
MUST BE  
PARALLEL  
TO THE  
CENTER LINE  
OF THE  
VEHICLE  
AZ MOTOR  
LNBF  
VOLTAGE  
REFLECTOR  
CONTROL BOX DETAIL  
ELECTRONICS INTERIOR VIEW  
Vehicle  
Front  
(#1 represents Switch DOWN; #0 represents Switch up)  
A
Sat. Rcvr. Mt. Option  
Switch Set Position  
Mount  
Option A  
...........................  
1
2
3
4
5
6
7
8
DIRECTV ...................... A ....... 0 .. 0 .. 0 .. 0 . 0 .. 0 .. 0 .. 1  
(FACTORY PRESET)  
Vehicle  
Front  
DIRECTV ..................... B ....... 1 .. 0 .. 0 .. 0 . 0 .. 0 .. 0 .. 1  
DISH NETWORK ................. A ....... 0 .. 0 .. 0 .. 1 . 0 .. 0 .. 1 .. 1  
DISH NETWORK ................. B ......... 1 .. 0 .. 0 .. 1 . 0 .. 0 .. 1 .. 1  
ExpressVu ................... A ....... 0 .. 1 .. 0 .. 1 . 1 .. 0 .. 1 .. 1  
ExpressVu ................... B ....... 1 .. 1 .. 0 .. 1 . 1 .. 0 .. 1 .. 1  
RECEIVER  
LNBF  
B
Mount  
Option B  
P4  
P3  
ELEVATION AZIMUTH  
7
 
Installation  
Installing unit on roof of vehicle —  
6. Place the unit on the roof in its permanent loca-  
tion and mark around the base bracket, Figure 4.  
(Make sure the rear adjustable base foot is par-  
allel with the center line of the vehicle. Refer  
to page 3, Figure 1A ).  
Install in DRY conditions only!  
!
IMPORTANT! Do not install this system  
in the rain, or under any wet conditions. Mois-  
ture may affect electronics and void your  
warranty!  
1. For best performance and to reduce signal ac-  
quisition time, park vehicle on a level surface; level  
the RV.  
7. Clean roof area where the base feet will be at-  
tached to the roof. Do not erase your marks!  
FIGURE 4  
2. Select a level spot on your roof for installation.  
Obstruction Ht. Unit Clearance  
Using the chart,  
determine the  
minimum distances  
8” .......................................... 4”  
10” ................................... 11.5”  
12” ...................................... 19”  
to other equipment.  
15” ...................................... 32”  
FIGURE 3  
UNIT BASE  
8. Put approved sealant in the areas marked  
for the base feet. Place base feet on top of the  
sealant and screw down with the (4) #10  
screws (provided) for each foot.  
9. After all base feet are secured to roof, put  
sealant around edge of feet and over screws.  
Replace base on screws and reinstall nut.  
WARNING: Level the base front to back and  
side to side. If base is not level the MV-4002 may  
require more time to locate the correct satellite  
or may not locate the correct satellite.  
• Be sure no roof-mounted equipment is  
blocking the satellite “line of sight”, Fig. 3  
You will need to decide where the wires will enter  
the vehicle.Acoax and a power wire (minimum 16  
gauge) will need to be run into the vehicle.  
BASE EXTERIOR  
FIGURE 5  
WARNING: Many +12VDC sources can cause the unit  
to fail. Select a filtered source, preferably a dedi-  
cated line to the battery.  
3. Remove dome. Place dome in safe spot to avoid  
damage. Place base on vehicle roof in the location  
selected.  
4. Attach each mounting foot to base by securing  
with two 7/16” nylocks. See page 7 for foot locations.  
5. After selecting location for unit (see number 2),  
put the unit on the centerline of the vehicle.  
REAR MOUNTING FOOT MUST BE PARALLEL  
WITH THE CENTER LINE OF VEHICLE. See pg. 7.  
8
 
Installation  
GPS installation —  
INSTALLING THE POWER SWITCH  
10. The GPS antenna is pre-wired and has a 1 meter  
cable running through one of the connectors.  
1. Choose a location to install the MV-4002 power  
ON/OFF switch. Remember when selecting a location  
that you will need to run the +12VDC power cable from  
the MV-4002 to the switch. Be sure the switch is in  
the OFF position before continuing. See Figure 9  
page 10.  
Determine location for GPS antenna. It is recom-  
mended you place the GPS antenna 3 feet from dome.  
The recommended location for the GPS antenna is  
based on having a level location and a clear view of the  
sky for the best satellite signal acquisition. Do not se-  
cure GPS antenna to roof at this time.  
Wall or panel mount: Drill 1-1/4” hole, pull wires  
through wall or panel.  
IMPORTANT! The GPS must be located minimum of 3  
feet away from obstructions on roof of vehicle. Antenna  
must have a clear view of the sky for proper op-  
eration.  
Surface mount: Determine location and direction of  
box. Mount box and feed wire into one of the box open  
ings. Select plate cover (brown or white provided) and  
snap the rocker switch into the switch plate. Be sure  
switch is off!  
Cable entry installation —  
2. Connect the ground wire from the vehicle and the  
BLACK ground wire from the MV-4002 together,  
using large yellow spade connector.  
1. Decide the best location for the cables to enter the  
vehicle, and the location of the switch and receiver  
(see “Installing the switch and receiver”on page 10). Drill  
a 1/2” hole in the roof, push wires inside. Make proper  
connections.  
3. Connect the YELLOW spade connector to  
the silver spade on the switch.  
You must have filtered +12 VDC power source.  
4. Connect the RED wire from the MV unit to the  
small RED spade connector.  
2. Place cable-entry plate over hole and cables. Screw  
in place. Seal plate and screw holes with approved seal-  
ant (not included).  
5. Connect small RED spade connector to center  
spade on switch.  
6. Connect the +12 V power wire from the vehicle to  
a small RED spade connector.  
3. Depending on the length of the cable on the roof, you  
may need to use cable clamps or wire ties (not pro-  
vided) between the unit and your cable-entry plate.  
Clamping the cable every 12”-16” should eliminate any  
unnecessary cable movement, Figure 6.  
7. Connect small RED spade connect to isolated  
spade on switch.  
INSTALLING THE POWER SWITCH DIAGRAM  
FIGURE 5  
ON/OFF ROCKER SWITCH  
WITH LIGHT  
(Shown in OFF position.)  
CABLE-  
ENTRY  
CABLE  
CLAMPS  
FIGURE 4  
INSTALLING THE DOME  
Insert screw in holes on dome  
rim. Be sure bolt is vertical;  
not tilted to side. Tighten to  
20 in-lb., or approximately  
until washer is visible  
QUADREX  
SCREW WITH  
RUBBER  
WASHER  
(USE #2  
PHILLIPS)  
STEPS 2 & 3  
STEPS 6 &7  
TWO GROUND WIRES  
+12 V FROM VEHICLE  
1 FROM VEHICLE  
1 BLACK WIRE FROM  
SATELLITE DISH  
around screw head.  
STEPS 4 & 5  
RED POWER  
WIRE FROM  
DISH  
CAUTION:  
DO NOT  
Terminals on switch have to be bent to fit in surface  
mount box.  
OVERTIGHTEN!!  
9
 
Installation • Wiring  
Connecting the receiver —  
WIRING TWO RECEIVERS  
NOT USED  
MV-4002 Tracking System  
Connecting one receiver  
1. Mount the DC Passive D575p demultiplexer in the  
same cabinet as your receiver.  
INPUT  
D575p DEMULTIPLEXER  
2. Connect the coax cable from the roof to the “input” on  
the DC Passive D575p demultiplexer. Connect a coax  
cable from the “sat receiver” on the DC Passive  
demultiplexer. Connect other end of this cable to “satel-  
lite in” on receiver.  
SAT RECEIVER  
SATELLITE IN  
PRIMARY RECEIVER  
OUT  
DEMULTIPLEXER  
DC BLOCK  
SP-2052  
IN  
WIRING ONE RECEIVER  
INPUT RECEIVER  
OUT  
SECONDARY  
NOT USED  
SATELLITE  
INPUT  
D575p  
DEMULTIPLEXER  
DC PASSIVE  
SAT RECEIVER  
Initializing —  
1. Be sure vehicle is in a location free of all obstruc-  
tions and with a clear view of the southern sky.  
SATELLITE IN  
2. DO NOT MOVE VEHICLE during the first  
initialization. Power up unit, turn on receiver. FOR  
THE FIRST TIME ONLY, the unit may take up to  
10 minutes to initially find the satellite signal. The  
GPS is also initializing at this time. After the GPS  
initializes, the unit will begin searching for the  
correct satellite. See page 4 for detail of operation.  
Connecting two receivers  
Connecting first receiver:  
1. Inside the vehicle, connect the coax cable from the  
roof to the “IN” input on the splitter (SP-2052). Connect  
a coax cable from one of the “OUT” ports or jack on the  
splitter (SP-2052). Connect other end of this cable to  
the “input” on the DC PASSIVE D575p demultiplexer.  
3. If the GPS does not initialize at this time, turn  
off the unit. You may need to move the GPS  
antenna to a different location on your roof.After  
you move the GPS, DO NOT SECURE TO ROOF.  
2. The primary receiver is the one used most often.  
This receiver will also control the satellite dish.  
4. TEST YOUR SYSTEM BEFORE SECURING  
THE GPS ANTENNA. Make sure the  
3. Connect a coax cable from the “satellite receiver”  
output on the DC PASSIVE D575p demultiplexer. Con-  
nect the other end of this cable to “Satellite IN”  
on the primary receiver.  
TV/receiver has found the correct satellite.  
5. After the correct satellite has been found, secure  
GPS antenna by removing adhesive backing  
and securing to roof.  
Connecting the second receiver:  
4. Connect a coax cable from the other “OUT” output  
on the splitter (SP-2052). Connect the other end of this  
cable to the “input” on the DC BLOCK demultiplexer.  
5. Connect a coax cable from the “receiver” output on the  
DC BLOCK demultiplexer. Connect the other end of this  
cable to “Satellite IN” on the secondary receiver.  
6. This receiver will only view the satellite that the main  
receiver is on.It will never toggle on it’s on.  
10  
 
Troubleshooting  
SOLUTION  
PROBLEM  
1. Check your Power switch to verify that it is in the ON position.  
The MV-4002 does not attempt to find a satellite or  
it never moves.  
2. Make sure that the receiver is plugged in and the satellite in jack is  
connected to MV-4002.  
3. Verify that the MV-4002 has had it’s three shipping straps re-  
moved. These straps are located inside the dome and keeps the  
dish from moving until it is installed.  
1. Wait 10 minutes. The unit can take up to 10 minutes to acquire  
GPS. If it normally takes 10 minutes to acquire GPS, contact  
Winegard.  
The MV-4002 turns on and moves for a few seconds  
then stops and never moves again.  
2. If you feel comfortable doing so, look on the roof of the vehicle to  
verify that the GPS antenna is at least 3 feet from the dome and  
other objects on roof. Failure to have the GPS antenna at least 3  
feet away can cause the dome to interfere with GPS aquisition. If  
antenna is too close, move it.  
3. Check the GPS antenna cable for damage. If there is a  
pinched or damaged section, contact Winegard.  
1. Make sure that your receiver is set up correctly.  
The dish never stops on any of the signals that  
it sees.  
For DISH Network, the check switch should read either “Un-  
known” or “SW42”.  
For DirecTV the receiver should be set for a Two Satellite Oval  
Dish.  
2. Make sure the receiver has power and the satellite dish is con-  
nected to the “Sat In”.  
With DirecTV, the Dish will find the alternate  
Satellite but it never finds the primary satellite.  
Make sure that the Switches on the Electronics Control Box are  
set for DirecTV. See page 3. These switches are found under  
the dome, inside the Electronics Control Box.  
1. Most likely the dish has locked on the satellite. Sometimes  
the receiver refuses to show it until its ready. To help it get  
ready, turn the receiver, not the dish, OFF. Wait a few minutes  
and turn it back on.  
The Dish stopped searching and is making little  
circles in the same area but I don’t have a signal.  
2. For Dish Network users, the Dish might be set to find DirecTV.  
See page 3 for instructions on setting it for Dish Network.  
1. Go to the check switch menu in receiver. Make sure that it’s  
set for SW42 and lists both even and odd transponders on sat-  
ellites 110 and 119.  
I am not getting all the Dish Network channels  
I subscribed to.  
The MV-4002 never sees any signals, it just keeps  
searching.  
1. Rain, Snow or excessive Dew on the dome can interrupt the  
signal. Snow and Dew can be brushed off the dome. If Heavy rain  
or Snow fall is blocking the signal, it may be necessary to wait  
until the weather clears.  
2. Check to see if the Southern sky is clear. Trees, Buildings, Large  
signs or an Overpass can block the signal. Find an area where you  
can be sure that this is not the problem and try again.  
3. Make sure the receiver has power and the satellite dish is  
connected to the “Sat In”.  
4. Verify electronics board inside dome is installed in proper loca-  
tion. Board should be placed so that magnets on unit’s gears  
pass through electronics board slot without hitting interior boards.  
Verify that the switches are set for the install option used for  
your vehicle. Option A has the rear mounting foot facing off the  
back of the vehicle. Option B has the rear mounting foot facing  
off the front of vehicle. See page 3 for switch settings.  
The MV-4002 works when it is stationary but fails  
when the vehicle is in motion.  
11  
 
Specifications & Warranty  
Features and specifications  
• One button operation.  
• 30’ power cable and 30’ coaxial cable included.  
• Dome UV protected.  
• GPS satellite signal acquisition.  
• Depending on receiver type, you can access  
satellites 119°, 110°, 101° or 92°.  
• Off-white color compatible with all vehicles.  
• Compact size —  
• No user input required.  
• No data port required for DISH NetworkTM,  
DIRECTV® or ExpressVu.  
32” diameter, 15.75” height  
Weight of unit - 32 lbs.  
Shipping weight - 44 lbs.  
• Operating temperature  
-13°F to +140°F  
• Tracking greater than 30°/sec.  
• Elevation range 14.5° to 74.5°;  
azimuth unlimited.  
TWO YEAR LIMITED WARRANTY  
Winegard Company warrants this Winegard product (excluding receiver) against any defects in materials or  
workmanship within two (2) years from date of purchase. No warranty claim will be honored unless at the time the claim  
is made, you present proof of purchase to an authorized Winegard dealer (if unknown, please contact Winegard  
Company, 3000 Kirkwood Street, Burlington, Iowa 52601-2000, telephone 319-754-0600).  
Winegard Company (at its option) will either repair or replace the defective product at no charge to you. This warranty  
covers parts, but does not cover any costs incurred in removal, shipping or reinstallation of the product. This limited  
warranty does not apply if the product is damaged, deteriorates, malfunctions or fails from: misuse, improper  
installation, abuse, neglect, accident, tampering, modification of the product as originally manufactured by Winegard,  
usage not in accordance with product instructions or acts of nature such as damage caused by wind, lightning, ice or  
corrosive environments such as salt spray and acid rain.  
The Two Year Warranty is provided on the condition that the equipment is properly delivered with all handling and  
freight charges prepaid to your Winegard dealer for repair or return to our factory at the above address. Winegard  
dealers will arrange for the replacement or repair and return to you, without charge, the product which failed due to  
defective material or workmanship.  
WINEGARD COMPANY WILL NOT ASSUME ANY LIABILITIES FOR ANY OTHER WARRANTIES, EXPRESS OR  
IMPLIED, MADE BY ANY OTHER PERSON.  
ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING WARRANTIES OF  
FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY ARE LIMITED TO THE TWO YEAR PERIOD  
OF THIS WRITTEN WARRANTY.  
The foregoing shall be the sole and exclusive remedy of any person whether in contract, tort or otherwise, and  
Winegard shall not be liable for incidental or consequential damage or commercial loss, or from any other loss or  
damage except as set forth above.  
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion of limitation of incidental  
or consequential damages, so the above limitations or exclusions may not apply to you.  
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.  
Printed in U.S.A. © 2005 Winegard Company 2452062 Rev. 5/05  
12  
 

Westinghouse Computer Monitor LCM 19v5 User Manual
Whirlpool Ice Maker 2208357 User Manual
Whirlpool Range W10394384A User Manual
Winegard Satellite TV System PM 2000 User Manual
Wolf Convection Oven WKGHD2 User Manual
Woodstock Cordless Sander D3736 User Manual
X10 Wireless Technology Home Security System MS12A User Manual
Xerox Copier C2128 User Manual
Zanussi Dishwasher ZSF 6171 User Manual
Zanussi Washer FL 12 User Manual