Xantech Stereo System HDMI1X2 User Manual

HDMI1X2  
USER MANUAL  
 
INTRODUCTION  
The Xantech 1X2 Splitter for HDMI 1.3  
The Xantech 1X2 Splitter for HDMI 1.3 allows set-top boxes, DVD players, Blu-  
ray players and other HDTV devices with HDMI outputs to be connected to up  
to two HDTV displays (or more if multiple splitters are utilized in place of HDTV  
displays).  
How It Works  
The Xantech 1X2 Splitter for HDMI 1.3 is a distribution hub that sends the  
same HDMI signals to two HDMI-compatible digital display devices. An HDMI  
video source is connected to the input jack on the 1X2 Splitter for HDMI 1.3.  
HDMI-compatible displays are connected to each of the HDMI outputs on the  
1X2 Splitter, and beautiful, sharp HDMI video will then emerge on all of your  
connected displays.  
READ THESE NOTES BEFORE INSTALLING OR  
OPERATING THE XANTECH 1X2 SPLITTER FOR HDMI 1.3  
By default, display information from the display connected to HDMI output port 1 is  
sent back to the source. Therefore, the other display connected to the 1X2 Splitter  
for HDMI 1.3 must be capable of accepting the timings and resolutions of the  
display that is connected to HDMI output port 1. It is recommended that the display  
with the lowest native resolution be connected to HDMI output port 1. This is to  
ensure that a compatible video signal will be able to be displayed on all connected  
monitors. There is a generic EDID programmed into the 1X2 Splitter for HDMI 1.3  
that can be used instead. Please see page 5 for more details.  
The Xantech 1x2 Splitter for HDMI 1.3 is HDMI/HDCP compliant and is  
compatible with all HDMI and DVI* displays.  
*When used with a DVI-to-HDMI cable or adapter  
-1-  
 
FEATURES  
Features  
Connects up to two HDMI / DVI displays from one HDMI source  
Optionally add more displays by connecting splitters  
Easily attains resolutions up to 1080p, 2k, and 1920 x 1200  
HDMI and HDCP compliant  
HDMI 1.3 Features  
Lip-Sync Pass Through  
225 MHz (up to 12 bit YUV 444 supported @ 1080p)  
Deep Color Supported (XV Color Supported)  
Color Space Conversion Supported  
Dolby TrueHD & DTS-HD Master Audio Supported  
CEC Pass Through  
INCLUDED IN THE PACKAGE  
(1) 1X2 Splitter for HDMI 1.3  
(1) 6 ft HDMI-to-HDMI Cable (M-M)  
(1) 5V DC Power Supply  
(1) User’s Manual  
-2-  
 
PANEL LAYOUT AND DESCRIPTIONS  
Front Panel  
1
2
3
4
Back Panel  
5
6
7
8
9
10  
1
2
Power LED  
This LED will activate once a valid power source is applied.  
Internal EDID LED  
This LED will activate only when the pre-programmed internal EDID is being  
used. Please see page 5 for more details on the internal EDID.  
3
External EDID LED (default EDID routing)  
This LED will activate only when the external EDID is being used. Please see  
page 5 for more details on the external EDID.  
4
5
Link LED  
This LED activates when a valid link between the source and splitter is detected.  
EDID Button  
This button will activate the onboard EDID. Press this button (the Int. EDID  
should turn on and the Ext. LED should turn off) and reset the unit using the  
Reset button (below) to initialize this EDID mode. To use an external EDID, press  
the EDID button again (the Int. LED should turn off and the Ext. LED should turn  
on) and press the Reset button to initialize this EDID mode.  
6
Reset Button  
This button will reset the unit and initialize whichever EDID mode is currently  
selected.  
-3-  
 
PANEL DESCRIPTIONS, CONTINUED  
7
8
HDMI Input  
This is the input for the HDMI source device. When a valid source is detected by  
the splitter, the Link LED will activate.  
HDMI Out 1  
This is the rst HDMI output port. Connect a valid HDMI display to this port.  
When the External EDID mode is active, the EDID form the display connected to  
this port will be used to send to the source.  
9
HDMI Out 2  
This is the second HDMI output port. Connect a valid HDMI display to this port.  
10 5V DC Power Input  
This port is for the included 5V DC power supply. When a valid 5V power supply  
is attached, the Power LED will activate.  
-4-  
 
CONNECTING THE 1X2 SPLITTER FOR HDMI 1.3  
How to Connect the 1X2 Splitter For HDMI 1.3  
1. Connect the supplied cable from the HDMI source into the 1X2 Splitter for HDMI 1.3  
input.  
2. Connect the cables from your displays (monitor or projector) into the HDMI outs  
of the 1X2 Splitter for HDMI 1.3. Up to 2 displays are supported.  
3. Plug the 5V DC power supply into the 1X2 Splitter for HDMI 1.3.  
NOTE: By Default, the display information from the display connected to HDMI output  
port 1 is sent back to the source. Therefore, the other display that is connected to the  
1X2 Splitter for HDMI 1.3 must be capable of accepting the timings and resolutions of the  
display that is connected to HDMI output port 1. It is recommended that the display with  
the lowest native resolution be connected to HDMI output port 1. This is to ensure that a  
compatible video signal will be able to be displayed on all connected monitors. There is  
a generic EDID programmed into the 1X2 Splitter for HDMI 1.3 that can be used instead.  
Please see below for the activation process.  
EDID MODE  
The HDMI1X2 has an EDID button which will determine if the EDID is used from the  
display attached to output 1 (Ext. mode) or if the onboard EDID (Int. mode) will be  
used.  
The current EDID mode can be determined by which EDID mode LED is active on  
the front panel. The Ext LED will indicate that the external EDID (from output port 1)  
is being used, and the Int LED will indicate that the internal pre-programmed EDID is  
being used.  
If you want to use the onboard EDID, press the EDID button on the rear panel and  
then press the reset button to activate the new EDID mode. To revert back to using  
the external EDID, press the EDID button again and then reset the unit using the reset  
button to activate the new EDID mode.  
Listed Resolutions in the Internal EDID:  
1280x720p  
1280x720p  
1920 x 1080i  
1920 x 1080i  
720 x 480p  
720 x 576p  
1920 x 1080p  
1920 x 1080p  
1440 x 480p  
1440 x 576p  
50 Hz  
(Native)  
59.94 / 60 Hz (Native)  
50 Hz  
59.94 / 60 Hz  
59.94 / 60 Hz  
50 Hz  
50 Hz  
59.94 / 60 Hz  
59.94 / 60 Hz  
50 Hz  
-5-  
 
SPECIFICATIONS  
Video Amplier Bandwidth: 225 MHz  
Input Video Signal: 12 Volts p-p  
Input DDC Signal: 5 Volts p-p (TTL)  
Single Link Range: 1080p/1920 x 1200, 12 bit color depth  
HDMI Connector: Type A 19 Pin Female  
Power Supply: 5V DC  
Power Consumption: 10 Watts (max)  
Dimensions: 10.25”W x 1”H x 4.25”D  
Shipping Weight: 5 lbs  
Technical Support  
Mailing Address  
Hours: 7AM-5:30PM PST  
Xantech Corporation  
Phone: 800.843.5465  
press 2 for Tech Support  
FAX: 800.492.6832  
13100 Telfair Avenue, 2/F  
Sylmar, CA 91342  
HDMI1X2 User Manual © 2008 Xantech Corporation  
This document is copyright protected. No part of this manual may be copied or  
reproduced in any form without prior written consent from Xantech Corporation.  
Xantech Corporation shall not be liable for operational, technical, or editorial  
errors/omissions made in this document. Xantech is a registered trademark of  
Xantech Corporation. All rights reserved.  
-6-  
 

Wells Saw M 36 3 User Manual
West Bend Coffeemaker 56600 User Manual
Whirlpool Air Conditioner RH123A1 User Manual
Whirlpool Clothes Dryer 3XWED5705SW0 User Manual
Whirlpool Range 8053373A User Manual
White Rodgers Thermostat 37E73A 918 User Manual
Winegard TV Antenna HD 9022 User Manual
Wolfgang Puck Coffeemaker Model BCM00020 User Manual
Yamaha Stereo Amplifier AX 1090 User Manual
Zanussi Freezer 51FF User Manual